Skip to main content
🏭 HANWEI Noise Barriers · Built to Block Noise. 🌐 中文站 📞 +86 18831881133
📞 +86 18831881133On call 24/7
  1. Home
  2. /
  3. Articles
  4. /
  5. NRC vs STC: What Importers Should Actually Check
Technical

NRC vs STC: What Importers Should Actually Check on Acoustic Panels

Updated Nov 19, 2026 7 min read By Li Gong, Export Desk

NRC and STC are not competitors — they measure opposite directions of the same problem, and a noise barrier needs both. NRC tells you how much sound the panel surface absorbs. STC tells you how much sound it stops from passing through. Buyers who treat them as interchangeable end up with one of two classic failures: a wall that blocks sound beautifully while the yard behind it echoes like a stadium, or a soft, absorbent panel that barely blocks anything.

NRC: how much sound the surface soaks up

NRC (Noise Reduction Coefficient) is a single number between 0 and 1. A panel with NRC 0.85 absorbs 85% of the sound energy that reaches it and reflects the rest.

Absorption matters wherever sound can bounce: the face of a barrier beside a highway, the inside of an equipment enclosure, the walls around a cooling tower. If the surface reflects, reflected energy finds another path — over the wall, around it, or back toward the source side.

Practical benchmark: for roadside absorptive barriers, insist on NRC ≥ 0.85. Our absorptive panels get there with an 80 mm centrifugal glass wool core behind a perforated face. Below about 0.70, the "absorptive" label is doing more marketing than physics.

STC: how much sound the panel blocks

STC (Sound Transmission Class) rates airborne sound insulation — how much quieter it is on the far side of the panel. Higher is better, and mass plus airtightness drive it.

Our post-and-panel systems insulate 25–40 dB(A) depending on construction: single leaf at the lower end, composite absorptive panels at the upper end. Remember the installed wall performs below the panel figure, because sound bends over the top edge — barrier type selection explains the height and distance logic.

The two numbers on one project

WhereWhat mattersWhat to specify
Highway barrier facing homesBothAbsorptive panel: NRC ≥ 0.85 face, 25–40 dB(A) insulation
Plant boundary wallInsulationReflective panel, insulation-first design
Enclosure interiorAbsorptionNRC ≥ 0.85 lining, solid outer shell
Cooling tower screenAbsorption + airflowAbsorptive louvre sized to required airflow

What to ask a Chinese supplier for

Numbers on a website are claims. Documents in the shipment are evidence. Before you place an order:

  • Batch test reports for the acoustic core — the report for the goods you receive, not a five-year-old lab sample.
  • Zinc thickness readings for galvanized posts and brackets, taken per batch.
  • Material certificates accompanying the shipment, in English.
  • A specification sheet that states core density, panel thickness and coating weight as numbers you can measure on arrival.

We issue English documentation with every batch — test reports, zinc readings and material certificates — so your inspector verifies against the purchase specification instead of trusting a brochure. That is also why vetting a manufacturer starts with the paperwork, not the price.

Reading the numbers on a datasheet

When a supplier sends a panel datasheet, four lines do the talking: core type and thickness (our absorptive panels use 80 mm centrifugal glass wool), face perforation (open area percentage, not "perforated"), coating weight for the steel, and the stated figures with a document behind them. A datasheet that lists NRC and STC but ships no batch report is a brochure, not a specification.

One more importer's note: absorptive performance is measured on the finished panel — perforated face, core and all — not on the raw wool. If a quote swaps the core density after order confirmation, the NRC on the datasheet no longer describes your panels. Tie the datasheet to the batch in the purchase contract.

Bottom line

Specify absorption and insulation as two separate lines in your purchase specification, demand the documents that prove both, and the panels that arrive will do what the quotation promised. Send us your noise target — we will size the construction and return a written specification with the quotation within 24 hours.

Frequently asked questions

What is the difference between NRC and STC?

NRC (Noise Reduction Coefficient, 0 to 1) measures how much sound a surface absorbs — high NRC stops reflections. STC (Sound Transmission Class) measures how much sound a panel blocks from passing through it — high STC means quiet behind the panel. One panel cannot be judged by either number alone.

What NRC should an absorptive barrier panel have?

Look for NRC ≥ 0.85, which our absorptive panels achieve with an 80 mm centrifugal glass wool core. Anything below roughly 0.70 leaves enough reflection to undermine the barrier on the opposite side of a roadway.

How much sound does a barrier panel block?

Our post-and-panel systems insulate 25–40 dB(A) panel-to-panel, depending on construction. Behind an installed barrier the measured reduction at the receiver is 10–25 dB, because sound bends over the top edge of the wall.

What test documents should come with an order?

Batch test reports for the acoustic core, zinc thickness readings for galvanized steel, and material certificates accompanying the shipment. We provide English documentation with every batch so your inspector can verify against the purchase specification on arrival.

Work with HANWEI

Turn the guide into a specification

Send your barrier length, target height and the noise source — a written specification and quotation come back within 24 hours, and the export desk is on call 24/7 (GMT+8).

Why Us

8 Reasons to Choose HANWEI

13-year acoustic product manufacturer · Manufactured, tested and shipped from one factory

01
🏭

Direct Factory Supply

Own factory with 5,000㎡ daily capacity — galvanized steel, aluminum and acoustic panels all produced in-house. No middlemen, no markups.

02
📐

Acoustic Support Before Production

Send your drawings or noise data and our engineers return a barrier cross-section, an insertion-loss estimate and a bill of materials in English — before any steel is cut.

03
🎯

One Factory, Full Production Chain

Slitting, punching, roll forming, galvanizing, powder coating, panel assembly and mounting hardware all under one roof, so posts and panels always match and one order carries one quality standard.

04
🌏

Export Delivery Record

Products delivered across China and shipped to Southeast Asia, the Middle East and Africa — highway and railway barriers, community screens, acoustic panels, silencers and louvres.

05
🔬

Documented Acoustic Performance

Composite barrier noise reduction of 10–25dB(A) and NRC ≥ 0.85 on 80 mm absorptive cores. Laboratory test reports ship with the delivery so you can verify the figures yourself.

06
🏅

Complete Documentation

Material certificates, coating thickness records and acoustic test reports are issued for every production batch, ready for tender submission and site acceptance.

07
🛡️

Engineered for Site Conditions

Post and foundation design is calculated against the wind pressure and seismic zone that apply on your site, using the code your project is approved under.

08
⚡

Fast Delivery

Standard configurations on stocked tooling ship in 7 to 15 days; double shifts are arranged for urgent projects.

Email Us Get a Quote